Authentication is the verification of a user's identity, usually through username/password credentials. Authorization is allowing a certain action to be applied to a particular path based on authentication of the originator.
Generally, authorization is a two step process. First authentication, using a username/password database. Second authorization, determining what the username is allowed to do for this transaction.
Basic authorization was discussed in "WASD VMS Web Services - Install and Config"; 13 - Authorization Configuration (Basics) WASD Web Services - Install and Config ). This section discusses all the aspects of WASD authentication and authorization.
By default, the logical name WASD_CONFIG_AUTH locates a common authorization rule file. Simple editing of the file and reloading into the running server changes the processing rules.
Server authorization is performed using a configuration file, authentication source, and optional full-access and read-only authorization grouping sources, and is based on per-path directives. There is no user-configured authorization necessary, or possible! In the configuration file paths are associated with the authentication and authorization environments, and so become subject to the HTTPd authorization mechanism. Reiterating ... WASD HTTPd authorization administration involves those two aspects, setting authorization against paths and administering the authentication and authorization sources.
Authorization is applied to the request path (i.e. the path in the URL used by the client). Sometimes it is possible to access the same resource using different paths. Where this can occur care must be exercised to authorize all possible paths.
Where a request will result in script activation, authorization is performed on both script and path components. First script access is checked for any authorization, then the path component is independently authorized. Either may result in an authorization challenge/failure. This behaviour can be disabled using a path SETting rule, see "WASD VMS Web Services - Install and Config"; 12.5.5 - SET Rule WASD Web Services - Install and Config ).
The authentication source name is refered to as the realm, and refers to a collection of usernames and passwords. It can be the system's SYSUAF database.
The authorization source is refered to as the group, and commonly refers to a collection of usernames and associated permissions.
The configuration file rules are scanned from first towards last, until a matching rule is encountered (or end-of-file). Generally a rule has a trailing wildcard to indicate that all sub-paths are subject to the same authorization requirements.
Rule matching is string pattern matching, comparing the request specified path, and optionally other components of the request when using configuration conditionals (see "WASD VMS Web Services - Install and Config"; 7 - Conditional Configuration WASD Web Services - Install and Config ), to a series of patterns, until one of the patterns matches, at which stage the authorization characteristics are applied to the request and authentication processing is undertaken. If a matching pattern (rule) is not found the path is considered not to be subject to authorization. Both wildcard and regular expression based pattern matching is available (see "WASD VMS Web Services - Install and Config"; 6 - String Matching WASD Web Services - Install and Config ).
A policy regarding when and how authorization can be used may be established on a per-server basis. This can restrict authentication challenges to "https:" (SSL) requests (4 - Transport Layer Security), thereby ensuring that the authorization environment is not compromised by use in non-encrypted transactions. Two server qualifiers provide this.
Note also that individual paths may be restricted to SSL requests using either the mapping conditional rule configuration or the authorization configuration files. See "WASD VMS Web Services - Install and Config"; 12.9 - Conditional Mapping WASD Web Services - Install and Config and Access Restriction Keywords.
In addition, the following configuration parameters have a direct role in an established authorization policy.
Authentication Cache and Revalidation
User revalidation relies on an entry being maintained in the authentication cache. Each time the entry is flushed, for whatever reason (cache congestion, command-line purge, server restart, etc.), the user will be prompted for credentials. It may be necessary to increase the size of the cache by adjusting [AuthCacheEntriesMax] when this facility is enabled.
Details of authentication failures are logged to the server process log.
Failures may also be directed to the OPCOM facility (see "WASD VMS Web Services - Install and Config"; 4.11 - OPCOM Logging WASD Web Services - Install and Config ).
Both paths and usernames have permissions associated with them. A path may be specified as read-only, read and write, write-only (yes, I'm sure someone will want this!), or none (permission to do nothing). A username may be specified as read capable, read and write capable, or only write capable. For each transaction these two are combined to determine the maximum level of access allowed. The allowed action is the logical AND of the path and username permissions.
The permissions may be described using the HTTP method names, or using the more concise abbreviations R, W, and R+W.
|
Requiring a particular path to be authorized in the HTTP transaction is accomplished by applying authorization requirements against that path in a configuration file. This is an activity distinct from setting up and maintaining any authentication/authorization databases required for the environment.
By default, the system-table logical name WASD_CONFIG_AUTH locates a common authorization configuration file, unless an individual rule file is specified using a job-table logical name. Simple editing of the file changes the configuration. Comment lines may be included by prefixing them with the hash "#" character, and lines continued by placing the backslash character "\" as the last character on a line.
The [IncludeFile] is a directive common to all WASD configuration, allowing a separate file to be included as a part of the current configuration. See (see "WASD VMS Web Services - Install and Config"; 4.1 - Include File Directive WASD Web Services - Install and Config ).
Configuration directives begin either with a "[realm]", "[realm;group]" or "[realm;group-r+w;group-r]" specification, with the forward-slash of a path specification, or with a "[AuthProxy]" or "[AuthProxyFile]" introducing a proxy mapping. Following the path specification are HTTP method keywords controlling group and world permissions to the path, and any access-restricting request scheme ("https:") and/or host address(es) and/or username(s).
Square brackets are used to enclose a [realm;group;group] specification, introducing a new authentication grouping. Within these brackets is specified the realm name (authentication source), and then optional group (authorization source) names separated by semi-colons. All path specifications following this are authenticated against the specified realm database, and permissions obtained from the group "[realm;group]" database (or authentication database if group not specified), until the next [realm;group;group] specification.
The following shows the format of an authentication source (realm) only directive.
[authentication-source]
This one, the format of a directive using both authentication and authorization sources (both realm and group).
[authentication-source ; authorization-source]
The third variation, using an authentication, full-access (read and write) and read-only authorization sources (realm and two grouping).
[authentication-source ; full-access-source ; read-only-source]
The authentication source may also be given a description. This is the text the browser dialog presents during password prompting. See Realm Description in 3.5 - Authentication Sources.
Paths are usually specified terminated with an asterisk wildcard. This implies that any directory tree below this is included in the access control. Wildcards may be used to match any portion of the specified path, or not at all. Following the path specification are control keywords representing the HTTP methods or permissions that can be applied against the path, and optional access-restricting list of host address(es) and/or username(s), separated using commas. Access control is against either or both the group and the world. The group access is specified first followed by a semi-colon separated world specification. The following show the format of the path directive, see the examples below to further clarify the format.
/root/path/ group-access-list,group-permissions ; \
world-access-list,world-permissions
The [AuthProxy] and [AuthProxyFile] directives introduces one or more SYSUAF proxy mappings (3.10.5 - VMS Account Proxying).
The same path cannot be specified against two different realms for the same virtual service. The reason lies in the HTTP authentication schema, which allows for only one realm in an authentication dialog. How would the server decide which realm to use in the authentication challenge? Of course, different parts of a given tree may have different authorizations, however any tree ending in an asterisk results in the entire sub-tree being controlled by the specified authorization environment, unless a separate specification exists for some inferior portion of the tree.
There is a thirty-one character limit on authentication source names.
The following realm names are reserved and have special functionality.
By default accounts with SYSPRV authorized are always rejected to discourage the use of potentially significant usernames (e.g. SYSTEM). Accounts that are disusered, have passwords that have expired, or that are captive or restricted are also automatically rejected.
The authentication source may be disguised by giving it a specific description. This will the text the browser dialog presents during password prompting. See Realm Description in 3.5 - Authentication Sources.
See 3.10 - SYSUAF-Authenticated Users for further information on these topics.
The following username is reserved.
If a host name, protocol identifier or username is included in the path configuration directive it acts to further limit access to matching clients (path and username permissions still apply). If more than one are included a request must match each. If multiple host names and/or usernames are included the client must match at least one of each. Host and username strings may contains the asterisk wildcard, matching one or more consecutive characters. This is most useful when restricting access to all hosts within a given domain, etc. In addition a VMS security profile may be associated with the request.
/web/secret/* *.three.stooges,~Moe,~Larry,~Curly,readrestricts read access to Curly, Larry and Moe accessing from within the three.stooges network, while
/web/secret/* https:,*.three.stooges,~Moe,~Larry,~Curly,readapplies the further restriction of access via "https:" (SSL) only.
These examples show the use of a network mask to restrict based on the source network of the client. The first, four octets supplied as a mask. The second a VLSM used to specify the length of the network component of the address.
/web/secret/* https:,#131.185.250.128/255.255.255.192,~Moe,~Larry,~Curly,read /web/secret/* https:,#131.185.250.128/26,~Moe,~Larry,~Curly,read
These examples both specify a 6 bit subnet. With the above examples the host 131.185.250.250 would be accepted, but 131.185.250.50 would be rejected.
Note that it more efficient to place protocol and host restrictions at the front of a list.
Authentication credentials may be validated against one of several sources, each with different characteristics.
An identifier is indicated by appending a "=ID" to the name of the realm or group. Also refer to 3.10.3 - Rights Identifiers.
Whether or not any particular username is allowed to authenticate via the SYSUAF may be controlled by that account holding or not holding a particular rights identifier. Placing "=ID" against realm name implies the username must exist in the SYSUAF and hold the specified identifier name.
[PROJECT_A=id]
When (and only when) a username has been authenticated via the SYSUAF, rights identifiers associated with that account may be used to control the level-of-access within that realm. This is in addition to any identifier controlling authentication itself.
[PROJECT_A=id;PROJECT_A_LIBRARIAN=id;PROJECT_A_USER=id]
In this example a username would need to hold the PROJECT_A identifier to be able to authenticate, PROJECT_A_LIBRARIAN to write the path(s) (via POST, PUT) and PROJECT_A_USER to be able to read the path(s).
The server system SYSUAF may be used to authenticate usernames using the VMS account name and password. The realm being VMS may be indicated by using the name "VMS", by appending "=VMS" to another name making it a VMS synonym, or by giving it a specific description (Realm Description in 3.5 - Authentication Sources). Further information on SYSUAF authentication may be found in 3.10 - SYSUAF-Authenticated Users. These examples illustrate the general idea.
[VMS] [LOCAL=vms] [ANY_NAME_AT_ALL=vms]
Three Authentication and Credential Management Extension (ACME) agents are currently available (as at VMS V8.3 and WASD v9.3), "VMS" (SYSUAF), "MSV1_0" (Microsoft domain authentication used by Advanced Server) and an LDAP kit. There is also an API that will allow local or third-party agents to be developed. WASD ACME authentication is completely asynchronous and so agents that make network or other relatively latent queries will not add granularity into server processing. By default ACME is used to authenticate requests against the SYSUAF on Alpha and Itanium running VMS V7.3 or later (3.10.1 - ACME).
For authorization rules explicitly specifying ACME the Domain Of Interpretation (DOI) becomes the realm name, interposed between the relam description and the ACME authentication source keyword. In this first example the DOI is VMS and so all WASD SYSUAF authentication capabilities are available.
["ACME Coyote"=VMS=ACME;JIN_PROJECT=id] /a/path/* r+w,https:
In the second example authentication is performed using the same credentials as Advanced Server running on the local system.
["PC Users"=MSV1_0=ACME] /a/nuther/path/* r+w,https:
In this final example the DOI is a third-party agent.
["More ACME"=THIRD-PARTY=ACME] /a/different/path/* r+w,https:
A plain-text list may be used to provide usernames for group membership. The format is one username per line, at the start of the line, with optional, white-space delimited text continuing along the line (which could be used as documentation). Blank lines and comment lines are ignored. A line may be continued by ending it with a "\" character. These files may, of course, be created and maintained using any plain text editor. They must exist in the WASD_AUTH: directory, have an extension of ".$HTL", and do not need to be world accessible.
# the stooges curley Jerome Horwitz larry Louis Feinberg moe Moses Horwitz shemp Samuel Horwitz JoeBesser JoeDeRita
Simple lists are indicated in the configuration by appending a "=LIST" to the name.
[VMS;STOOGES=list]
It also possible to use a simple list for authentication purposes. The plain-text password is appended to the username with a trailing equate symbol. Although in general this is not recommended as everything is stored as plain-text it may be suitable as an ad hoc solution in some circumstances. The following example shows the format.
# silly example fred=dancesalittle Guess who? ginger=rogers No second prizes!
These are binary, fixed 512 byte record files, containing authentication and authorization information. HTA databases may be used for authentication and group membership purposes. The content is much the same, the role differs according to the location in the realm directive. These databases may be administered using the online Server Administration facility (9.5 - HTTPd Server Revise) or the HTAdmin command-line utility (13.8 - HTAdmin). They are located in the WASD_AUTH: directory and have an extension of ".$HTA".
(Essentially for historical reasons) HTA databases are the default sources for authorization information. Therefore, using just a name, with no trailing "=something", will configure an HTA source. Also, and recommended for clearly showing the intention, appending the "=HTA" qualifier specifies an HTA database. The following example show some of the variations.
[VMS;PROJECT_A=hta] [DEVELOPERS=hta;PROJECT_A=hta]
Uses X.509 v3 certificates (browser client certificates) to establish identity (authentication) and based on that identity control access to server resources (authorization). This is only available for SSL transactions. See 4 - Transport Layer Security for further information on SSL, and 4.5.12 - Authorization Using X.509 Certification on X509 realm authorization.
From RFC1413 (M. St.Johns, 1993) ...
The Identification Protocol (a.k.a., "ident", a.k.a., "the Ident Protocol") provides a means to determine the identity of a user of a particular TCP connection. Given a TCP port number pair, it returns a character string which identifies the owner of that connection on the server's system.
and ...
The information returned by this protocol is at most as trustworthy as the host providing it OR the organization operating the host. For example, a PC in an open lab has few if any controls on it to prevent a user from having this protocol return any identifier the user wants. Likewise, if the host has been compromised the information returned may be completely erroneous and misleading.
The Identification Protocol is not intended as an authorization or access control protocol. At best, it provides some additional auditing information with respect to TCP connections. At worst, it can provide misleading, incorrect, or maliciously incorrect information.
Nevertheless, RFC1413 may be useful for some purposes in some heterogeneous environments, and so has been made available for authentication purposes.
[RFC1413] ["Descriptions can be used!"=RFC1413;A_PROJECT=list]
The RFC1413 realm generates no browser username/password dialog. It relies on the system supporting the client to return a reliable identification of the user accessing the HTTP server by looking-up the user of the server connection's peer port.
An authorization agent is a CGI-compliant CGIplus script that is specially activated during the authorization processing. Using CGI environment variables it gets details of the request, makes an assessment based on its own internal authentication/authorization processing, and using the script callout mechanism returns the results to the server, which then acting on these, allows or denies access.
Such agents allow a site to develop local authentication/authorization mechnisms relatively easily, based on CGI principles. A discussion of such a development is not within the scope of this section, see the WASD Web Services - Scripting document for information on the use of callouts, and the example and working authorization agents provided in the WASD_ROOT:[SRC.AGENT] directory. The description at the beginning of these programs covers these topics in some detail.
An authorization agent would be configured using something like the following, where the "AUTHAGENT" is the actual script name doing the authorization. This has the the path "/cgiauth-bin/" prepended to it.
["Example Agent"=AUTHAGENT_EXAMPLE=agent] /some/path/or/other/* r+w
It is possible to supply additional, per-path information to an agent. This can be any free-form text (up to a maximum length of 63 characters). This might be a configuration file location, as used in the example CEL authenticator. For example
["CEL Authenticator"=AUTHAGENT_CEL=agent] /some/path/or/other/* r+w,param=WASD_ROOT:[LOCAL]CEL1.LIS /a/nother/path/* r+w,param=WASD_ROOT:[LOCAL]CEL2.LIS
Generally authorization agent scripts use 401/WWW-Authorize: transactions to establish identity and credentials. It is possible for an agent to establish identity outside of this using mechanisms available only to itself. In this case it is necessary suppress the usually automatic generation of username/password dialogs using a realm of agent+opaque
[AUTHAGENT_PAPI=agent+opaque] /papi/path/or/other/* r+w /a/nother/papi/path/* r+w
An older mechanism required a leading parameter of "/NO401". It is included here only for reference. The agent+opaque realm should now always be used.
["Another Authenticator"=AUTHAGENT_ANOTHER=agent] /some/path/or/other/* r+w,param="/NO401 MORE PARAMETERS CAN BE SUPPLIED" /a/nother/path/* r+w,param="/NO401 OTHER PARAMETERS CAN BE SUPPLIED"
It is necessary to have the following entry in the WASD_CONFIG_MAP configuration file:
exec+ /cgiauth-bin/* /cgi-bin/*
This allows authentication scripts to be located outside of the general server tree if desired.
A token is a short-lived, cookie delivered, representation of authentication established in another context. Originally devised to allow controlled access to very large datasets without the overhead of SSL in the transmission but with access credentials supplied in the privacy of an SSL connection. The cookie contains NO CREDENTIAL data at all and the authenticator manages an internal database of these so it can determine whether any supplied token is valid and when that token has expired. By default (and commonly) token authorisation occurs in non-SSL space (http:) and the credential authorisation in SSL space (https:).
Token authorisation is described in 3.11 - Token Authentication).
Instead of a list of usernames contained in a database, a group within a realm (either or both full-access-source or read-only-source, see 3.4 - Authorization Configuration File) may be specified as a host, group of hosts or network mask. This acts to restrict all requests from clients not matching the IP address specification. Unlike the per-path access restrict list (Access Restriction Keywords) this construct applies to all paths in the realm. It also offers relative efficiencies over restriction lists and lends itself to some environments based on per-host identification (e.g. the RFC1413 realm). Note that IP addresses can be spoofed (impersonated) so this form of access control should be deployed with some caution.
[RFC1413;131.185.250.*] /path1/to/be/authorized/* r+w [RFC1413;131.185.250.0/24] /path2/to/be/authorized/* r+w [RFC1413;131.185.250.0/255.255.255.0] /path3/to/be/authorized/* r+w
The examples of realm specifications above all act to restrict read-write access via the RFC1413 realm to hosts within the 131.185.250.nnn subnet.
Generally the WASD model is for the server to perform authorisation processing and so the password never becomes visible at the application level. For scripting environments performing their own authentication the server will decode and parse the request "Authorization:" header for paths under the EXTERNAL realm.
[EXTERNAL] /some/path/or/other/* r+w
The various authentication data are then provided in the CGI variables
If the script is performing its own authentication and authorisation using the raw request header then the server needs to be advised of this by placing the required paths under the OPAQUE realm.
[OPAQUE] /another/path/* r+w
The server will then provide only the "Authorization:" header data in the cgi variable HTTP_AUTHORIZATION from which the username and password may processed.
A realm directive may contain one or more different types of authorization information source, with the following restrictions.
[DEVELOPERS;PROJECT_A=id] [DEVELOPERS=hta;LIBRARIAN=id;PROJECT_A=list] [STOOGES=list;MOE_HOWARD=id]
It is possible to supply text describing the authentication realm to the browser user that differs from the actual source name. This may be used to disguise the actual source or to provide a more informative description than the source name conveys.
Prefixing the actual realm source name with a double-quote delimited string (of up to 31 characters) and an equate symbol will result in the string being sent to a browser as the realm description during an authentication challenge. Here are some examples.
["the local host"=VMS] ["Social Club"=SOCIAL_CLUB_RW=id] ["Finance Staff"=FINANCE=list] ["Just Another Database"=DBACCESS=hta]
NOTE
The Digest authentication scheme uses the realm description at both server and browser in the encrypted password challenge and response. When passwords are stored in an HTA file this realm synonym cannot be changed without causing these passwords to be rendered invalid.
WASD authorization offers a number of combinations of access control. This is a summary. Please note that when refering to the level-of-access a particular username may be allowed (read-only or full, read-write access), that it is always moderated by the level-of-access provided with a path configured within that realm. See 3.3 - Permissions, Path and User.
When a path is controlled by a realm that comprises an authentication source only, as in this example
[authentication-source]usernames authenticated using that are granted full (read and write) access.
Where a group membership source is provided following the authentication source, as illustrated in this example
[authentication-source;group-source]the level-of-access depends on the source of the group membership. If from a simple-list of usernames or via a VMS rights identifier the username receives full (read and write) access. If from an HTA database the access is dependent on what is set against that user in the database. It can be either full or read-only.
When a second group is specified, as in
[authentication-source;group-source;group-source]the authentication is interpreted in a fixed fashion. The first group specified contains usernames to be granted full (read and write) access. The second group read-only access. Should a username occur in both groups full access takes precedence.
The second group may be specified as an asterisk wildcard ("*") which is interpreted as everyone else (i.e. everyone else gets read-only access).
As described in "WASD VMS Web Services - Install and Config"; 4.3 - Virtual Services WASD Web Services - Install and Config ), virtual service syntax may be used with authorization mapping to selectively apply rules to one specific service. This example provides the essentials of using this syntax. Note that service-specific and service-common rules may be mixed in any order allowing common authorization environments to be shared.
# authorization rules example for virtual servers [[alpha.example.com:443]] # ALPHA SSL is the only service permitting VMS (SYSUAF) authentication [LOCAL=vms] /web/* https:,r+w ; r /httpd/-/admin/* ~daniel,https:,r+w [[beta.example.com:80]] # BETA has its own HTA database [BETA_USER=hta] /web/* r+w ; r [[gamma.example.com:80]] # GAMMA likewise [GAMMA_DEVELOPER=id;PROJECT-A=list] /web/project/a/* r+w ; r [GAMMA_DEVELOPER=id;PROJECT-B=list] /web/project/b/* r+w ; r [[*]] # allow anyone from the local subnet to upload to here [WORLD] /web/unload/* 131.185.200.*,r+w
The online Server Administration facility path authorization report (9.4 - HTTPd Server Reports) provides a selector allowing the viewing and checking of rules showing all services or only one particular virtual server, making it simpler to see exactly what any particular service is authorizing against.
Mixed case is used in the configuration examples (and should be in configuration files) to assist in readability. Rule interpretation however is completely case-insensitive.
[WASD=vms;SOCIALCLUB=list] /web/socialclub/* r+w ; read
[WASD=vms;SOCIALCLUB=list] /web/socialclub/* 131.185.45.*,get,post; *.example.com,get /web/socialclub/accounts/* 131.185.45.*,~BLOGGS,get,post; *.example.com,get
[DEVELOPER=id;PROJECT_A_LIBRARIAN=id;PROJECT_A_USER=id] /web/projects/a/* r+w /web/projects/* r
[DEVELOPER=id;PROJECT_A_LIBRARIAN=id;*] /web/projects/a/* r+w /web/projects/* r
[ADMIN=hta] /web/everyone/* get,post;get /web/select/few/* get,post
["The Company"=COMPANY=hta] /web/docs/* ~Howard,~George,~Fred,r+w ; r /web/accounts/* ~George,r+w ; r
[VMS] /web/local/area/* 131.185.250.*,r+w ; r
["not the VMS SYSUAF"=VMS] /httpd/-/admin/* #localhost,~daniel,r+w
["Ident Protocol"=RFC1413;131.185.250.0/24] /web/local/* r+w
[WORLD] /web/scratch/* *.local.hosts.only,r+w
WASD authorization allows for very simple authorization environments and provides the scope for quite complex ones. The path authentication scheme allows for multiple, individually-maintained authentication and authorization databases that can then be administered by autonomous managers, applying to widely diverse paths, all under the ultimate control of the overall Web administrator.
Fortunately great complexity is not generally necessary.
Most sites would be expected to require only an elementary setup allowing a few selected Web information managers the ability to write to selected paths. This can best be provided with the one authentication database containing read and write permissions against each user, with and access-restriction list against individual paths.
For example. Consider a site with three departments, each of which wishes to have three representatives capable of administering the departmental Web information. Authentication is via the SYSUAF. Web administrators hold an approriate VMS rights identifier, "WEBADMIN". Department groupings are provided by three simple lists of names, including the Web administrators (whose rights identifier would not be applied if access control is via a simple list), a fourth lists those with read-only access into the Finance area. The four grouping files would look like:
# Department 1 # Department 2 WEB1 WEB1 WEB2 WEB2 JOHN RINGO PAUL CURLY GEORGE LARRY # Department 3 # Finance (read access) WEB1 PAUL WEB2 GEORGE MOE JOHN SHEMP RINGO MACThe authorization configuration file then contains:
#######################################################################
# allow web masters (!) to use the server administration facility
# to revise web configuration files
# world has no access (read or write)
# access is only allowed from a browser in the same subnet as the HTTPd
["Hypo Thetical Corp."=HYPOTHETICAL=vms;WEBADMIN=id]
/httpd/-/admin/* #150.15.30.*,r+w
/wasd_root/local/* #150.15.30.*,r+w
# allows Department 1 representatives to maintain their web
# this may only be done from within the company subnet
# world has read access
["Hypo Thetical Corp."=HYPOTHETICAL=vms;DEPARTMENT1=list]
/web/dept/general/* 150.15.30.*,r+w ; r
# and so on for the rest of the departments
["Hypo Thetical Corp."=HYPOTHETICAL=vms;DEPARTMENT2=list;FINANCE=list]
# no world read access into finance, only those in the FINANCE list
/web/dept/finance/* 150.15.30.*,r+w
["Hypo Thetical Corp."=HYPOTHETICAL=vms;DEPARTMENT3=list]
/web/dept/inventory/* 150.15.30.*,r+w ; r
/web/dept/production/* 150.15.30.*,r+w ; r
# (the next uses line continuation just for illustration)
/web/dept/marketing/* 150.15.30.*,\
r+w ;\
read
# we need an area for general POSTing (just for illustration :-)
[WORLD]
/web/world/* r+w
#######################################################################
Access to authentication sources, SYSUAF, simple lists and HTA databases, are relatively expensive operations. To reduce the impact of this activity on request latency and general server performance, authentication and realm-associated permissions for each authenticated username are stored in a cache. This means that only the initial request needs to be checked from appropriate databases, subsequent ones are resolved more quickly and efficiently from cache.
Such cached entries have a finite lifetime associated with them. This ensures that authorization information associated with that user is regularly refreshed. This period, in minutes, is set using the [AuthCacheMinutes] configuration parameter. Zero disables caching with a consequent impact on performance.
Where-ever a cache is employed there arises the problem of keeping the contents current. The simple lifetime on entries in the authentication cache means they will only be checked for currency whenever it expires. Changes may have occured to the databases in the meantime.
Generally there is are other considerations when adding user access. Previously the user attempt failed (and was evaluated each time), now the user is allowed access and the result is cached.
When removing or modifying access for a user the cached contents must be taken into account. The user will continue to experience the previous level of access until the cache lifetime expires on the entry. When making such changes it is recommended to explicitly purge the authentication cache either from the command line using /DO=AUTH=PURGE (9.7 - HTTPd Command Line) or via the Server Administration facility (9 - Server Administration). Of course the other solution is just to disable caching, which is a less than optimal solution.
The ability to authenticate using the system's SYSUAF is controlled by the server /SYSUAF[=keyword] qualifier. By default it is disabled.
WARNING!
SYSUAF authentication is not recommended except in the most secure of LAN environments or when SSL is employed.HTTP credentials (username and password) are transmitted as encoded plain-text making them vulnerable to evesdropping.
By default accounts with SYSPRV authorized are always rejected to discourage the use of potentially significant usernames (e.g. SYSTEM). This behaviour can be changed through the use of specific identifiers, see 3.10.3 - Rights Identifiers immediately below. Accounts that are disusered, have passwords that have expired or that are captive or restricted are always rejected. Accounts that have access day/time restricting access will have those restrictions honoured (see 3.10.3 - Rights Identifiers for a workaround for this).
Also see 3.10.6 - Nil-Access VMS Accounts.
By default the Authentication and Credential Management Extension (ACME) is used to authenticate SYSUAF requests on Alpha and Itanium running VMS V7.3 or later (3.5 - Authentication Sources). VAX and earlier versions of VMS use WASD's own SYSUAF authentication routines. The advantage of ACME is with the processing of the (rather complex) authentication requirements by a vendor-supplied implementation. It also allows SYSUAF password change to be made subject to the full site policy (password history, dictionary checking, etc.) which WASD does not implement.
By default SYSUAF authentication uses the NETWORK access restriction from the account SYSUAF record. Alternatives LOCAL, DIALUP and REMOTE may be specified using global configuration directive
# WASD_CONFIG_GLOBAL [AuthSYSUAFlogonType] REMOTEand/or authorization rule parameter 'param="logon=REMOTE"'
["VMS Credentials"=WASD_VMS_RW=ID] /secured/* r+w,https,param="logon=REMOTE"(which takes precedence).
Whether or not any particular username is allowed to authenticate via the SYSUAF may be controlled by that account holding or not holding a particular VMS rights identifier. When a username has been authenticated via the SYSUAF, rights identifiers associated with that account may be used to control the level-of-access within that realm.
Use of identifiers for these purposes are enabled using the /SYSUAF=ID server startup qualifier.
The first three reserved identifier names are optional. A warning will be reported during startup if these are not found. The fourth must exist if SYSUAF proxy mappings are used in a /SYSUAF=ID environment.
Identifiers may be managed using the following commands. If unsure of the security implications of this action consult the relevant VMS system management security documentation.
$ SET DEFAULT SYS$SYSTEM $ MCR AUTHORIZE UAF> ADD /IDENTIFIER WASD_HTTPS_ONLY UAF> ADD /IDENTIFIER PROJECT_USER UAF> ADD /IDENTIFIER PROJECT_DEVELOPER UAF> ADD /IDENTIFIER PROJECT_LIBRARIAN
They can then be provided to desired accounts using commands similar to the following:
UAF> GRANT /IDENTIFIER PROJECT_USER <account>
and removed using:
UAF> REVOKE /IDENTIFIER PROJECT_USER <account>
Be aware that, as with all successful authentications, and due to the WASD internal authentication cache, changing database contents does not immediately affect access. Any change in the RIGHTSLIST won't be reflected until the cache entry expires or it is explicitly flushed (3.9 - Authorization Cache).
Deprecated and Discouraged
As this has been deprecated for some years now the documentation for this functionality has been removed.
For backward-reference see the "WASD Hypertext Services - Technical Overview" document for release v9.3 or earlier.
Any authentication realm can have its usernames mapped into VMS usernames and the VMS username used as if it had been authenticated from the SYSUAF. This is a form of proxy access.
CAUTION
This is an extremely powerful mechanism and as a consequence requires enabling on the command-line at server startup using the /SYSUAF=PROXY qualifier and keyword. If identifiers are used to control SYSUAF authentication (i.e. /SYSUAF=ID) then any account mapped by proxy access must hold the WASD_PROXY_ACCESS identifier described in 3.10.3 - Rights Identifiers (and server startup would be something like "/SYSUAF=(ID,PROXY)").
When a proxy mapping occurs request user authorization detail reflects the SYSUAF username characteristics, not the actual original authentication source. This includes username, user details (i.e. becomes that derived from the owner field in the SYSUAF), constraints on the username access (e.g. SSL only), and user capabilities including any profile if enabled. Authorization source detail remains unchanged, reflecting the realm, realm description and group of the original source. For CGI scripting an additional variable, WWW_AUTH_REMOTE_USER, provides the original remote username.
For each realm, and even for each path, a different collection of mappings can be applied. Proxy entries are strings containing no white space. There are three basic variations, each with an optional host or network mask component.
The SYSUAF is the VMS username being mapped to. The remote is the remote username (CGI variable WWW_REMOTE_USER). The first variation maps a matching remote username (and optional host/network) onto the specific SYSUAF username. The second maps all remote usernames (and optional host/network) to the one SYSUAF username (useful as a final mapping). The third maps all remote usernames (optionally on the remote host/network) into the same SYSUAF username (again useful as a final mapping if there is a one-to-one equivalence between the systems).
Proxy mappings are processed sequentially from first to last until a matching rule is encountered. If none is found authorization is denied. Match-all and default mappings can be specified.
[RFC1413] [AuthProxy] bloggs@131.185.250.1=fred [AuthProxy] doe@131.185.250.*=john system=- *@131.185.252.0/24=* [AuthProxy] *=GUEST
In this example the username bloggs on system 131.185.250.1 can access as if the request had been authenticated via the SYSUAF using the username and password of FRED, although of course no SYSUAF username or password needs to be supplied. The same applies to the second mapping, doe on the remote system to JOHN on the VMS system. The third mapping disallows a system account ever being mapped to the VMS equivalent. The fourth, wildcard mapping, maps all accounts on all systems in 131.185.250.0 8 bit subnet to the same VMS username on the server system. The fifth mapping provides a default username for all other remote usernames (and used like this would terminate further mapping).
Note that multiple, space-separated proxy entries may be placed on a single line. In this case they are processed from left to right and first to last.
["Just an Example"=EXAMPLE=list] [AuthProxy] bloggs@131.185.250.1=fred doe@131.185.250.1=doe system=- \ *@131.185.252.0/24=* *=GUEST
Proxy mapping rules should be placed after a realm specification and before any authorization path rules in that realm. In this way the mappings will apply to all rules in that realm. It is possible to change the mappings between rules. Just insert the new mappings before the (first) rule they apply to. This cancels any previous mappings and starts a new set. This is an example.
["A Bunch of Users"=USERS=hta] [AuthProxy] bloggs@131.185.250.1=fred doe@131.185.250.1=john /fred/and/johns/path/* r+w [AuthProxy] *=GUEST /other/path/* read
An alternative to in-line proxy mapping is to provide the mappings in one or more independent files. In-line and in-file mappings may be combined.
["Another Bunch of Users"=MORE_USERS=hta] [AuthProxy] SYSTEM=- [AuthProxyFile] WASD_ROOT:[LOCAL]PROXY.CONF /path/for/proxy* r+w
To cancel all mappings for following rules use an [AuthProxy] (with no following mapping detail). Previous mappings are always cancelled with the start of a new realm specification. Where proxy mapping is not enabled at the command line or a proxy file cannot be loaded at startup a proxy entry is inserted preventing all access to the path.
REMEMBER - proxy processing can be observed using the WATCH facility.
It is possible, and may be quite effective for some environments, to have a SYSUAF account or accounts strictly for HTTP authorization, with no actual interactive or other access allowed to the VMS system itself. This would relax the caution on the use of SYSUAF authentication outside of SSL transactions. An obvious use would be for the HTTP server administrator. Additional accounts could be provided for other authorization requirements, all without compromising the system's security.
In setting up such an environment it is vital to ensure the HTTPd server is started using the /SYSUAF=ID qualifier (3.2 - Authentication Policy). This will require all SYSUAF-authenticated accounts to possess a specific VMS resource identifier, accounts that do not possess the identifier cannot be used for HTTP authentication. In addition the identifier WASD_NIL_ACCESS will need to be held (3.10.3 - Rights Identifiers), allowing the account to authenticate despite being restricted by REMOTE and NETWORK time restrictions.
To provide such an account select a group number that is currently unused for any other purpose. Create the desired account using whatever local utility is used then activate VMS AUTHORIZE and effectively disable access to that account from all sources and grant the appropriate access identifier (see 3.10.3 - Rights Identifiers above).
$ SET DEFAULT SYS$SYSTEM $ MCR AUTHORIZE UAF> MODIFY <account> /NOINTERACTIVE /NONETWORK /NOBATCH /FLAG=DISMAIL UAF> GRANT /IDENTIFIER WASD_VMS_RW <account>
When SSL is in use (4 - Transport Layer Security) the username/password authentication information is inherently secured via the encrypted communications of SSL. To enforce access to be via SSL add the following to the WASD_CONFIG_MAP configuration file:
/whatever/path/you/like/* "403 Access denied." ![sc:https]or alternatively the following to the WASD_CONFIG_AUTH configuration file:
[REALM] /whatever/path/you/like/* https:
Note that this mechanism is applied after any path and method assessment made by the server's authentication schema.
The qualifier /SYSUAF=SSL provides a powerful mechanism for protecting SYSUAF authentication, restricting SYSUAF authenticated transactions to the SSL environment. The combination /SYSUAF=(SSL,ID) is particularly effective.
Also see 3.2 - Authentication Policy.
It is possible to control access to files and directories based on the VMS security profile of a SYSUAF-authenticated remote user. This functionality is implemented using VMS security system services involving SYSUAF and RIGHTSLIST information. The feature must be explicitly allowed using the server /PROFILE qualifier. By default it is disabled.
NOTE
Use caution when deploying the /PROFILE qualifier. It was really designed with a very specific environment in mind, that of an Intranet where the sole purpose was to provide VMS users access to their normal VMS resources via a Web interface.
When a SYSUAF-authenticated user (i.e. the VMS realm) is first authenticated a VMS security-profile is created and stored in the authentication cache (3.9 - Authorization Cache). A cached profile is an efficient method of implementing this as it obviously removes the need of creating a user profile each time a resource is assessed. If this profile exists in the cache it is attached to each request authenticated for that user. As it is cached for a period, any change to a user's security profile in the SYSUAF or RIGHTSLIST won't be reflected in the cached profile until the cache entry expires or it is explicitly flushed (9.6 - HTTPd Server Action).
When a request has this security profile all accesses to files and directories are assessed against it. When a file or directory access is requested the security-profile is employed by a VMS security system service to assess the access. If allowed, it is provided via the SYSTEM file protection field. Hence it is possible to be eligible for access via the OWNER field but not actually be able to access it because of SYSTEM field protections! If not allowed, a "no privilege" error is generated.
Once enabled using /PROFILE it can be applied to all SYSUAF authenticated paths, but must be enabled on a per-path basis, using the WASD_CONFIG_AUTH profile keyword (Access Restriction Keywords)
# WASD_CONFIG_AUTH [VMS;VMS] /wasd_root/local/* profile,https:,r+wor the WASD_CONFIG_MAP SET profile and noprofile mapping rules (see "WASD VMS Web Services - Install and Config"; 12.5.5 - SET Rule WASD Web Services - Install and Config ).
# WASD_CONFIG_MAP set /wasd_root/local/* profile set * noprofile
Of course, this functionality only provides access for the server, IT DOES NOT PROPAGATE TO ANY SCRIPT ACCESS. If scripts must have a similar ability they should implement their own scheme (which is not too difficult, see WASD_ROOT:[SRC.MISC]CHKACC.C ) based on the CGI variable WWW_AUTH_REALM which would be "VMS" indicating SYSUAF-authentication, and the authenticated name in WWW_REMOTE_USER.
If the /PROFILE qualifier has enabled SYSUAF-authenticated security profiles, whenever a file or directory is assessed for access an explicit VMS security system service call is made. This call builds a security profile of the object being assessed, compares the cached user security profile and returns an indication whether access is permitted or forbidden. This is addition to any such assessments made by the file system as it is accessed.
This extra security assessment is not done for non-SYSUAF-authenticated accesses within the same server.
For file access this extra overhead is negligible but becomes more significant with directory listings ("Index of") where each file in the directory is independently assessed for access.
Much of a site's package directory tree is inaccessible to the server account. One use of the SYSUAF profile functionality is to allow authenticated accesss to all files in that tree. This can accomplished by creating a specific mapping for this purpose, subjecting that to SYSUAF authentication with /PROFILE behaviour enabled (3.10.8 - SYSUAF Security Profile), and limiting the access to a SYSTEM group account. As all files in the WASD package are owned by SYSTEM the security profile used allows access to all files.
The following example shows a path with a leading dollar (to differentiate it from general access) being mapped into the package tree. The "set * noprofile" limits the application of this to the /$WASD_ROOT/ path (with the inline "profile").
# WASD_CONFIG_MAP set * noprofile . . . pass /wasd_root/* /wasd_root/* pass /$WASD_ROOT/* /wasd_root/* profile
This path is then subjected to SYSUAF authentication with access limited to an SSL request from a specific IP address (the site administrator's) and the SYSTEM account.
# WASD_CONFIG_AUTH [["/$WASD_ROOT/ Access"=WASD_TREE_ACCESS=id]] /$WASD_ROOT/* https,10.1.1.2,~system,read
This is a niche authorisation environment for addressing niche requirements.
A token is an HTTP cookie delivered representation of authentication established in another context. Originally devised to allow controlled access to very large datasets without the overhead of SSL in the transmission but with access credentials supplied in the privacy of an SSL connection.
A common scenario is where the client starts off attempting to access a resource in non-SSL space which is controlled by token authentication. In the first instance the authenticator detects there is no access token present and redirects the client (browser) to the SSL equivalent of that space, where credentials can be supplied encrypted. In this example scenario the SSL area is controlled by WASD SYSUAF authentication (can be SSL client certificate, etc.) and the username/password is prompted for. When correctly entered this generates a token. The token is stored (with corresponding detail) as a record in a server-internal database and then returned to the browser as a set-cookie value.
With the token data stored the browser is transparently redirected back to the non-SSL space where the actual access is to be undertaken, this time the browser presenting the cookie containing the token. The authenticator examines the token, looking it up in the database. If found, has originated from the same IP address, represents the same authentication realm, and has not expired, it then allows the non-SSL space access to proceed, and in this example scenario the dataset transfer is initiated (in unencrypted clear-text). If the token is not found in the database or has expired, then the process is repeated with a redirect back into SSL space. If the realms differ a 403 forbidden response is issued (see configuration below).
The token itself is a significant sequence of pseudo-random characters, is short-lived (configurable as anything from a few seconds to a few tens of seconds, or more), and as a consequence is frequently regenerated. The token is just that, containing no actual credential data at all. It might be possible to snoop but as it contains nothing of value in itself, expires relatively quickly, and has an originating IP address check, the fairly remote risk of playback is just that.
The authenticator does all the work, implicitly redirecting the user from non-SSL space to SSL space for the original authentication, and then back again with the token used for access in the non-SSL space. With the expiry of a token it undertakes that cycle again, redirecting back to the SSL-space where the browser-cached credentials will be supplied automatically allowing the fresh token to be issued, and then redirected back into non-SSL space for access. To emphasise - all this is transparent to the user.
As a consequence of this model the resource being controlled can ONLY be accessed from non-SSL space using the controlled path. To access the same resource from SSL space a distinct path to the resource must be provided.
As token authorisation relies on the client agent having HTTP cookies enabled (globally or specifically for the site) it is useful to have this tested for and/or advised about, on some related but other area of the site. There are simple techniques using JavaScript for detecting the availability of cookie processing. Search the Web for a suitable solution.
The automatic authorisation and redirection occurs using a combination of two distinguishable authorisation rules, one for supplying the credentials, the other for using the token for authorisation. In this example (and commonly) the resources are at "/location/" and the configuration accepts user-supplied credentials in SSL space and uses the token in non-SSL space. The asterisk just indicates that in the absence of any other parameter this authorisation rule has a complementary token rule where access will actually occur.
# WASD_CONFIG_AUTH if (ssl:) ["VMS credentials"=WASD_VMS_RW=id+"TOKEN=*"] /location/* r+w else [WASD_VMS_RW=TOKEN] /location/* r+w endif
And in this example, the same arrangement but with non-standard ports (specified using an integer with a leading colon).
# WASD_CONFIG_AUTH if (ssl:) ["VMS credentials"=WASD_VMS_RW=id+"TOKEN=:7080"] /location/* r+w else [WASD_VMS_RW=TOKEN+"TOKEN=:7443"] /location/* r+w endif
To prevent potential thrashing, where multiple, distinct realms within a single request are authorised using tokens, corresponding multiple token (cookie) names must be used. It is expected that this would be an uncommon but not impossible scenario. The "thrashing" would be a result of authorisation associated with a single, particular token name. Where a realm differs from a previous token generated another is required. The token authorisation scheme forces the use of distinct token names by 403-forbidding change of realm using the one token. Use explicitly specified, independent token (cookie) names, or an integer preceded by an ampersand (which appends the integer to the base token name), ensuring the complementary rules are using the same name/integer.
# WASD_CONFIG_AUTH if (ssl:) ["VMS credentials"=WASD_VMS_RW=id+"TOKEN=&42"] /location/* r+w else [WASD_VMS_RW=TOKEN+"TOKEN=&42"] /location/* r+w endif
For the final example, the token is contained in the non-default cookie named "WaSd_example" and the authentication performed using an X509 client certificate (which can only be supplied via SSL).
# WASD_CONFIG_AUTH if (ssl:) [X509+"TOKEN=WaSd_example"] /location/* r+w else [X509=TOKEN+"TOKEN=WaSd_example"] /location/* r+w endif
Some additional detail is available from the AUTHTOKEN.C code module.
Provides a username and password that is authenticated from data placed into the global common (i.e. in memory) by the site administrator. The username and password expire (become non-effective) after a period, one hour by default or an interval specified when the username and password are registered.
It is a method for allowing ad hoc authenticated access to the server, primarily intended for non-configured access to the online Server Administration facilities (9.1 - Access Before Configuration) but is available for other purposes where a permanent username and password in an authentication database is not necessary. A skeleton-key authenticated request is subject to all other authorization processing (i.e. access restrictions, etc.), and can be controlled using the likes of '~_*', etc.
The site administrator uses the command line directive
$ HTTPD /DO=AUTH=SKELKEY=_username:password[:period]to set the username/password, and optionally the period in minutes. This authentication credential can be cancelled at any time using
$ HTTPD /DO=AUTH=SKELKEY=0
The username must begin with an underscore (to reduce the chances of clashing with a legitimate username) and have a minimum of 6 other characters. The password is delimited by a colon and must be at least 8 characters. The optional period in minutes can be from 1 to 10080 (one week). If not supplied it defaults to 60 (one hour). After the period expires the skeleton key is no longer accepted until reset.
NOTE
Choose username and password strings that are less-than-obvious and a period that's sufficient to the task! After all, it's your site that you might compromise!
The authentication process (with skeleton-key) is performed using these basic steps.
Note that the authenticator resumes looking for a username from a configured authentication source unless the request and skeleton-key usernames match. After that the passwords either match allowing access or do not match resulting in an authentication failure.
$ HTTPD /DO=AUTH=SKELKEY=_FRED2ACC:USE82PA55 $ HTTPD /DO=AUTH=SKELKEY=_ANDY2WERP:EGGO4TEE:10
The server account should have no direct write access to into any directory structure. Files in these areas should be owned by SYSTEM ([1,4]). Write access for the server into VMS directories (using the POST or PUT HTTP methods) should be controlled using VMS ACLs. This is in addition to the path authorization of the server itself of course! The recommendation to have no ownership of files and provide an ACE on required directories prevents inadvertant mapping/authorization of a path resulting in the ability to write somewhere not intended.
Two different ACEs implement two grades of access.
This example shows a suitable ACE that applies only to the original directory:
$ SET SECURITY directory.DIR - /ACL=(IDENT=HTTP$SERVER,ACCESS=READ+WRITE+EXECUTE+DELETE+CONTROL)This example shows setting an ACE that will propagate to created files and importantly, subdirectories:
$ SET SECURITY directory.DIR -
/ACL=((IDENT=HTTP$SERVER,OPTIONS=DEFAULT,ACCESS=READ+WRITE+EXECUTE+DELETE+CONTROL), -
(IDENT=HTTP$SERVER,ACCESS=READ+WRITE+EXECUTE+DELETE+CONTROL))
This example shows a suitable ACE that applies only to the original directory:
$ SET SECURITY directory.DIR - /ACL=(IDENT=HTTP$SERVER,ACCESS=READ+WRITE+EXECUTE+DELETE)This example shows setting an ACE that will propagate to created files and importantly, subdirectories:
$ SET SECURITY directory.DIR -
/ACL=((IDENT=HTTP$SERVER,OPTIONS=DEFAULT,ACCESS=READ+WRITE+EXECUTE+DELETE), -
(IDENT=HTTP$SERVER,ACCESS=READ+WRITE+EXECUTE+DELETE))
To assist with the setting of the required ACEs an example, general-purpose DCL procedure is provided, WASD_ROOT:[EXAMPLE]AUTHACE.COM.
Some sites may be sensitive enough about Web resources that the possibility of providing inadvertant access to some area or another is of major concern. WASD provides a facility that will automatically deny access to any path that does not appear in the authorization configuration file. This does mean that all paths requiring access must have authorization rules associated with them, but if something is missed some resource does not unexpectedly become visible.
At server startup the /AUTHORIZE=ALL qualifier enables this facility.
For paths that require authentication and authorization the standard realms and rules apply. To indicate that a particular path should be allowed access, but that no authorization applies the "NONE" realm may be used. The following example provides some indication of how it should be used.
# allow the librarian to update this area, world to read it [VMS;LIBRARIAN=id] /web/library/* r+w ; read # indicate there is no authorization to be applied [NONE] # allow access to general web areas /web/* # allow access to the WASD_ROOT tree /wasd_root/*
There is also a per-path equivalent of the /AUTHORIZE=ALL functionality, described in "WASD VMS Web Services - Install and Config"; 12.5.5 - SET Rule WASD Web Services - Install and Config . This allows a path tree to be require authorization be enabled against it.
# avoid an absence of authorization allowing unintentional access set /web/sensitive/* auth=all
The server provides for users to be able to change their own HTA passwords (and SYSUAF if required). This functionality, though desirable from the administrator's viewpoint, is not mandatory if the administrator is content to field any password changes, forgotten passwords, etc. Keep in mind that passwords, though not visible during entry, are passed to the server using clear-text form fields (which is why SSL is recommended).
Password modification is enabled by including a mapping rule to the internal change script. For example:
pass /httpd/-/change/* /httpd/-/change/*
Any database to be enabled for password modification must have a writable authorization path associated with it. For example:
[GROUP=id;GROUP=id] /httpd/-/change/group/* r+w [ANOTHER_GROUP=id;ANOTHER_GROUP=id] /httpd/-/change/another_group/* r+w
NOTE
What looks like redundancy in specifying an identical realm and group authorization is what allows multiple, independant identifiers to be individually controlled for password change (i.e. one group of identifier holders allowed to change the password, another not).
Use some form of cautionary wrapper if providing this functionality over something other than an Intranet or SSL connection:
<H2>Change Your Authentication</H2> <blockquote> Change the password used to identify yourself to the REALM Web environment for some actions. Note that this <U>not</U> an operating system password, nor has it anything to do with it. Due to the inherent weaknesses of using non-encrypted password transmissions on networks <FONT COLOR="#ff0000"><U>DO NOT</U> use a password you have in use anywhere else, especially an operating system password!</FONT> You need your current password to make the change. If you have forgotten what it is contact <A HREF="/web/webadmin.html">WebAdmin</A>, preferably via e-mail, for the change to be made on your behalf. </blockquote> <UL> <LI><A HREF="/httpd/-/change/REALM/">REALM</A> realm. </UL>
When using SYSUAF authentication it is possible for a password to pre-expired, or when a password lifetime is set for a password to expire and require respecification. By default an expired password cannot be used for access. This may be overridden using the following global configuration directive.
[AuthSYSUAFacceptExpPwd] enabled
Expired passwords may be specially processed by specifying a URL with WASD_CONFIG_GLOBAL [AuthSysUafPwdExpURL] configuration directive (see "WASD VMS Web Services - Install and Config"; 8.2 - Alphabetic Listing WASD Web Services - Install and Config ).
The WASD_CONFIG_MAP set auth=sysuaf=pwdexpurl=<string> rule allows the same URL to be specified on a per-path basis. When this is set a request requiring SYSUAF authentication that specifies a username with an expired password is redirected to the specified URL. This should directly or via an explanatory (wrapper) page redirect to the password change path described above. The password change dialog will have a small note indicating the password has expired and allows it to be changed.
The following WASD_CONFIG_GLOBAL directive
# WASD_CONFIG_GLOBAL [AuthSysUafPwdExpURL] https:///httpd/-/change/ # WASD_CONFIG_AUTH [WASD_VMS_ID=id;WASD_VMS_RW=id] /httpd/-/change/* r+wwould allow expired passwords to be changed.
It is also possible to redirect an expired password to a site-specific page for input and change. This allows some customization of the language and content of the expired password change dialog. An example document is provided at WASD_ROOT:[EXAMPLE]EXPIRED.SHTML (what it looks like) ready for relocation and customisation. Due to the complexities of passing realm information and then submitting that information to the server-internal change facility some dynamic processing is required via an SSI document.
This example assumes the site-specific document has been located at WEB:[000000]EXPIRED.SHTML and is accessed using SSL.
# WASD_CONFIG_GLOBAL [AuthSysUafPwdExpURL] https:///web/expired.shtml?httpd=ignore&realm=vms # WASD_CONFIG_AUTH [WASD_VMS_ID=id;WASD_VMS_RW=id] /httpd/-/change/vms/* r+w /web/expired.shtml r+w
The reason authorization information is not required to be reentered on subsequent accesses to controlled paths is cached information the browser maintains. It is sometimes desirable to be able to access the same path using different authentication credentials, and correspondingly it would be useful if a browser had a purge authorization cache button, but this is commonly not the case. To provide this functionality the server must be used to "trick" the browser into cancelling the authorization information for a particular path.
This is achieved by adding a specific query string to the path requiring cancellation. The server detects this and returns an authorization failure status (401) regardless of the contents of request "Authorization:" field. This results in the browser flushing that path from the authorization cache, effectively requiring new authorization information the next time that path is accessed.
There are two variations on this mechanism.
/the/current/path?httpd=logout
/the/current/path?httpd=logout
Also when using logout with a revalidation period a redirection URL may be appended to the logout query string. It then redirects to the supplied URL. It is important that the redirection is returned to the browser and not handled internally by WASD. Normal WASD redirection functionality applies.
?httpd=logout&goto=/// ?httpd=logout&goto=///help/logout.html ?httpd=logout&goto=http://the.host.name/
These examples redirect to
respectively.
Authentication Cache
User revalidation relies on an entry being maintained in the authentication cache. Each time the entry is flushed, for whatever reason (cache congestion, command-line purge, server restart, etc.), the user will be prompted for credentials. It may be necessary to increase the size of the cache by adjusting [AuthCacheEntriesMax].