1    /ADDRESS_COMPRESSION

    Indicates whether the address compression is on or off.

2    /ALL

       /ALL[=BRIEF] (default)
       /ALL[=LONG]

    Displays all the current device and communication settings. BRIEF
    formats the output for the screen. LONG displays each setting on
    a separate line.

3    /COUNTERS

       /COUNTERS=(keyword,...)

    Shows the current values for the specified counter(s). You
    can specify one or more of the following keywords with this
    qualifier:

    Keyword          Description

    ALL              Displays all counters.
    BAD_FCS_PACKETS  Displays the count of packets with bad frame
                     check sequence (FCS).
    DATA_LOST        Displays the count of lost characters that were
                     reported by hardware.
    DROPPED_         Displays the count of all characters thrown
    CHARACTERS       away.
    FRAMING_ERRORS   Displays the count of characters with framing
                     errors.
    LONG_PACKETS     Displays the count of packets longer than the
                     current maximum receive unit setting (MRU).
    RECEIVED_        Displays the count of total packets received.
    PACKETS
    RUNT_PACKETS     Displays the count of packets with too few
                     characters.
    TOTAL_           Displays the count of all characters received.
    CHARACTERS
    TRANSMITTED_     Displays the count of total packets transmitted.
    PACKETS

4    /ECHO

       /ECHO=(FAILURE=value, INTERVAL=value)

    Specifies the number of Link Control Protocol (LCP) echo requests
    and the interval (in milliseconds) between requests that must be
    sent without response before the line is considered down.

5    /FCS_SIZE

    Shows the current receive and transmit FCS size in bits.

6    /FLOW_CONTROL

       /FLOW_CONTROL=(keyword,...)

    Shows the current flow control setting used over the asynchronous
    physical link. You can specify one of the following keywords with
    this qualifier:

    Keyword    Description

    HARDWARE   Uses RTS/CTS flow control. If using this control, the
               transmit Asynch Control Character Map (ACCM) can be
               0x0, 0x0, 0x0, 0x60000000. Only valid for lines set to
               /MODEM or /COMMSYNCH.
    XON_XOFF   Uses band flow control. If using this control, the
    (de-       optimal transmit ACCM is 0xA0000, 0x0, 0x0, 0x60000000.
    fault)     Only valid for asynchronous lines.

7    /HANGUP

    Displays the action that occurs when a session is terminated.

8    /MAGIC_NUMBER_RETRIES

    Shows the number of attempts that are made to negotiate a magic
    number.

9    /MAXCONFIGURE

    Shows the number of configure-request packets sent without
    acknowledgment before assuming that the peer is not responding.

10    /MAXFAILURE

    Displays the number of configure-nak packets sent before sending
    a configure-ack and before assuming that the configuration is not
    converging.

11    /MAXTERMINATE

    Shows the number of terminate-request packets sent without
    acknowledgment before assuming the peer is unable to respond.

12    /MRU

    Displays the largest packet that the line can receive.

13    /MTU

    Displays the largest packet that the line can transmit.

14    /NETWORK_PROTOCOL

    Displays the current network protocol(s) allowed over the
    physical link.

15    /PASSIVE

    Indicates whether this is a passive or active line.

16    /PERMANENT

    Indicates whether this is a permanent or transient (nonpermanent)
    line.

17    /PROTOCOL_COMPRESSION

    Shows the status of protocol field compression.

18    /RECEIVE_ACCM

    Displays the value of the current receive ACCM for asynchronous
    ports.

19    /RESTART_TIMER

    Displays the interval used to time transmission of request
    packets.

20    /SPEED

    Indicates the current input and output speeds of the line.

21    /TRANSMIT_ACCM

    Displays the value of the current transmit ACCM for asynchronous
    ports.