o clns classes supported
Default: Class {4} Value: Bit-set
Set of protocol classes supported on the Connectionless Networt
Service (CLNS). You cannot modify this characteristic.
o cltp nsap selector (Tru64 UNIX)
Default: 0 Value: 0-255 (except 32)
The NSAP selector to use for CLTS when running over CLNS. If the
value is 0 or 1, a single NSAP is shared between the Connection-
Oriented Transport Service (COTS), and the connectionless
transport protocol according to the osi transport attribute nsap
selector. If both nsap selectors are 0 or 1, then COTS and CLTS
over CLNS are disabled.
This attribute cannot be set either to 32, which is the value
of the NSP NSAP selector, or to the current setting of the osi
transport attribute, nsap selector, if the attribute has a value
other than 0 or 1.
This attribute cannot be modified when transport is enabled.
o congestion avoidance
Default: True Value: True or false
Enables the use of the automatic congestion avoidance mechanism
to reduce the transport window size in response to an indication
from the Network layer when operating on the Connectionless
Network Service (CLNS).
o cons classes supported
Default: Classes {0, 2, 4} Value: set of classes
Set of protocol classes supported on the Connection-Oriented
Network Service (CONS). You cannot modify this characteristic.
See X.25/CONS Configuration for more information.
o cons filters
Default: { } Value: Set of simple names
The names of X.25 Access module filters used to determine which
inbound network connection requests should be directed to the
transport entity.
On OpenVMS Modification of this attribute while OSI transport is
enabled is permitted only with the add command. The set and
remove commands can only be used to modify this attribute when the
OSI transport is disabled.
For each cons filter, there must be a corresponding x25 access
template with the same name. One or more of these filters must be
specified in order to run COTS over CONS. The X.25 access filter
osi transport is typically used. See X.25/CONS Configuration for
more information.
o cons nsap addresses
Default: { } Value: Set of NSAP addresses
The set of valid NSAP addresses for use with CONS. One or more
NSAPs must be specified to run COTS over CONS. See the DECnet-Plus
for Tru64 UNIX Programming manual for more information.
o delay factor
Default: 4 Value: 2-15
Factor by which to multiply the current value of the round-trip
delay estimate status attribute in order to set a value for the
retransmission timer. This attribute works with protocol class 4
only.
o delay weight
Default: 5 Value: 0-255
Relative weighting to apply to the current estimate and to a new
sample when estimating round-trip delay. This attribute works
with protocol class 4 only.
o disconnect holdback
Default: 0 Value for Tru64 UNIX: 0-(2 raised to the
power of 31 -1)
Default: 0 Value for OpenVMS: 0-4294967295
When operating over the Connection-Oriented Network Service
(CONS), the length of the time to maintain a network connection
for possible reuse after all transport connections multiplexed
upon it have been disconnected. Specified in seconds. This
characteristic may not be changed while the transport entity
is enabled. See X.25/CONS Configuration for more information.
o dna version
Default: Value: V1.0.0
Version number of the DNA OSI Transport architecture
specification to which the implementation conforms. You cannot
modify this characteristic.
o iso version
Default: Value: 1
Version number of ISO 8073 to which the implementation
conforms. You cannot modify this characteristic.
o maximum cltp ports (Tru64 UNIX)
Default: 128 Value: 0-4294967295
Maximum number of CLTS ports at one time. This characteristic can
only be increased while transport is enabled. You can modify this
characteristic to a lower value only when the entity is disabled.
o maximum listeners (Tru64 UNIX)
Default: 32 Value: 1-65535
Maximum number of listeners at one time. This characteristic can
only be increased while transport is enabled. You can modify this
characteristic to a lower value only when the entity is disabled.
o maximum multiplexing
Default for Tru64 UNIX: 1023 Value: 1-1023
Default for OpenVMS: 4294967295 Value: 1-4294967295
When operating over the Connection-Oriented Network Service
(CONS), the maximum number of transport connections that can be
multiplexed on any single network connection. This characteristic
can be increased only when the transport entity is enabled.
You can modify this characteristic to a lower value only when
the entity is disabled. See X.25/CONS Configuration for more
information.
o maximum network connections
Default for Tru64 UNIX: 1023 Value: 0-1023
Default for OpenVMS: 4294967295 Value: 0-4294967295
When operating over the Connection-Oriented Network Service
(CONS), the maximum number of network connections which can be
in use concurrently by DNA OSI Transport. This characteristic
can be incresed only when the transport entity is enabled.
See X.25/CONS Configuration for more information.
o maximum receive buffers (OpenVMS)
Default: 2000 Value: 1-4294967295
Maximum number of receive buffers that can store received
DT transport PDUs. You can modify this characteristic only
when the entity is disabled. Also, you can only increase the
characteristic value.
o maximum remote nsaps
Default for Tru64 UNIX: 160 Value: 1-65536
Default for OpenVMS: 201 Value: 0-4294967295
Maximum number of remote NSAPs that can exist concurrently. This
value must be greater than the current value of maximum transport
connections. You can modify this characteristic to a lower value
only when the entity is disabled. This characteristic can be
increased when enabled.
o maximum transport connections
Default for Tru64 UNIX: 128 Value: 0-1023
Default for OpenVMS: 200 Value: 0-4294967295
Maximum number of active transport connections allowed at one
time. Must be less than the current value of maximum remote
nsaps. You can modify this characteristic to a lower value only
when the entity is disabled.
o maximum window
Default for Tru64 UNIX: 20 Value: 1-65535
Default for OpenVMS: 8 Value: 1-65535
Maximum credit window that can be granted on a transport
connection. This is used for control of the number of data
segments (PDUs) allowed to be transmitted over a particular
transport connection before at least one acknowledgment must
be returned from the destination system. If the number of
PDUs already transmitted equals the maximum window and no
corresponding acknowledgments have been received, transport
stops sending PDUs over the transport connection and waits for
an acknowledgment message. You can modify this characteristic to
a lower value only when the entity is disabled.
o nsap selector
Default: 33 Value: 0-255 (except 32)
The NSAP selector to use for the Connection-Oriented Transport
Service (COTS) when running over CLNS. If 0 or 1, COTS over CLNS
is not enabled. This attribute cannot be set to 32, which is the
value of the NSP NSAP selector. Or, on Tru64 UNIX, to the current
setting of the osi transport attribute cltp nsap selector if it
is other than 0 or 1.
This attribute cannot be modified when transport is enabled.
o RFC1006 listener ports (OpenVMS)
Default: { 102, 399 } Value: Set of TCP/IP port numbers
The names of the TCP listener ports used to receive inbound
RFC1006 connection requests. This is applicable for both RFC1006
and RFC1006 Extension connections.
Modification of this attribute while OSI transport is enabled is
permitted only with the add command. The set and remove commands
can only be used to modify this attribute when the OSI transport
is disabled.
o RFC1006 listener ipaddresses (OpenVMS)
Default: { 0.0.0.0 } Value: Set of IP Addresses
The names of the listener IP addresses used to receive inbound
RFC1006 connection requests. This is applicable for both RFC1006
and RFC1006 Extension connections.
Modification of this attribute while OSI transport is enabled is
permitted only with the add command. The set and remove commands
can only be used to modify this attribute when the OSI transport
is disabled.
o support map
Default: None Value: False
Specifies whether the implementation supports the MAP
(manufacturing automation protocol) entity. You cannot modify
this characteristic.