Library /sys$common/syshlp/helplib.hlb  —  INITIALIZE  /QUEUE  Examples
    1.$ INITIALIZE/QUEUE/PROCESSOR=TELNETSYM -
      _$ /ON="192.168.1.101:9100" SYS$PRINT

      This example initializes the SYS$PRINT print queue, specifying
      the TELNETSYM print symbiont, for the printer with the IP
      address 192.168.1.101 at TCP port 9100. For more information
      about TELNETSYM, see the TCP/IP Services for OpenVMS Management
      Guide.

    2.$ INITIALIZE/QUEUE/BATCH/START -
      _$ /AUTOSTART_ON=(DATA::, WARF::, DEANNA::) BATCH_1

      The INITIALIZE/QUEUE command in this example creates the
      batch queue BATCH_1, and designates it as an autostart queue
      capable of executing on node DATA, WARF, or DEANNA. The /START
      qualifier activates the queue for autostart. The queue will
      begin executing on the first node (in the list of nodes
      specified) for which the ENABLE AUTOSTART/QUEUES command is
      entered.

      If the node on which BATCH_1 is executing is taken out of the
      OpenVMS Cluster, the queue will be stopped on that node and
      will fail over to the first available node in the node list
      on which autostart is enabled for a queue manager SYS$QUEUE_
      MANAGER.

      As long as autostart is enabled on one of the nodes in the
      list, this queue will be started and available to execute batch
      jobs. If all three nodes in the example are shut down or if
      autostart is disabled, the queue will remain stopped until
      one of the three nodes in the node list joins the cluster and
      executes the ENABLE AUTOSTART/QUEUES command.

      The ENABLE AUTOSTART/QUEUES and INITIALIZE/QUEUE commands
      affect only the queues managed by the default queue manager
      SYS$QUEUE_MANAGER because the /NAME_OF_MANAGER qualifier is not
      specified.

    3.$ INITIALIZE/QUEUE/START/BATCH/JOB_LIMIT=3 SYS$BATCH
      $ INITIALIZE/QUEUE/START/BATCH/JOB_LIMIT=1/WSEXTENT=2000 BIG_BATCH

      In this example, the first INITIALIZE/QUEUE command creates
      a batch queue called SYS$BATCH that can be used for any batch
      job. The /JOB_LIMIT qualifier allows three jobs to execute
      concurrently. The second INITIALIZE/QUEUE command creates
      a second batch queue called BIG_BATCH that is designed for
      large jobs. Only one job can execute at a time. The working
      set extent can be as high as 125 pages on OpenVMS Alpha (on a
      system with 8KB pages).

    4.$ INITIALIZE/QUEUE/START/DEFAULT=(FLAG,TRAILER=ONE)-
      _$ /ON=LPA0: LPA0_PRINT
      $ INITIALIZE/QUEUE/START/DEFAULT=(FLAG,TRAILER=ONE)-
      _$ /BLOCK_LIMIT=(1000,"")/ON=LPB0: LPB0_PRINT
      $ INITIALIZE/QUEUE/START/GENERIC=(LPA0_PRINT,LPB0_PRINT) SYS$PRINT
      $ INITIALIZE/QUEUE/START/FORM_MOUNTED=LETTER-
      _$ /BLOCK_LIMIT=50/ON=TXA5: LQP

      In this example, the first three INITIALIZE/QUEUE commands set
      up printer queues. Both queue LPA0_PRINT and LPB0_PRINT are
      set up to put a flag page before each file within a job and a
      trailer page after only the last page in a job. In addition,
      LPB0_PRINT has a minimum block size of 1000; therefore, only
      print jobs larger than 1000 blocks can execute on that queue.
      SYS$PRINT is established as a generic queue that can direct
      jobs to either LPA0_PRINT or LPB0_PRINT. Jobs that are too
      small to run on LPB0_PRINT will be queued from SYS$PRINT to
      LPA0_PRINT.

      The last INITIALIZE/QUEUE command sets up a terminal queue on
      TXA5. A job queued with a form that has a stock type other
      than the stock type of form LETTER remains pending in the
      queue until a form with the same stock type is mounted on the
      queue, or until the entry is deleted from the queue or moved
      to another queue. LETTER has been established at this site to
      indicate special letterhead paper. The block size limit is 50,
      indicating that this queue is reserved for jobs smaller than
      51 blocks.

    5.$ INITIALIZE/QUEUE/ON=QUEBID::/BATCH/RAD=0   BATCHQ1

      $ SHOW QUEUE/FULL BATCHQ1
      Batch queue BATCHQ1, stopped, QUEBID::
       /BASE_PRIORITY=4 /JOB_LIMIT=1 /OWNER=[SYSTEM]
       /PROTECTION=(S:M,O:D,G:R,W:S) /RAD=0

      This example creates or reinitializes the batch queue BATCHQ1
      to run on node QUEBID. All jobs assigned to this queue will run
      on RAD 0.
Close Help