o data link port
Support: All
Name of the data link port used for this X.25 data adjacency.
This attribute is supported only if the owning routing circuit
entity's characteristic type is set to x25 da.
o dte address
Support: All
DTE address of the neighboring node on an X.25 circuit.
This status is supported only if the owning circuit entity's
characteristic type is x25 da.
o endnode ids
Support: All
System IDs of neighboring end nodes. This attribute is supported
only if the node is an end node and the owning circuit entity's
characteristic type is not x25 da.
o endnode nets
Support: All
NETs computed from the system IDs in the endnode ids status and
the set of area addresses in the owning routing entity's manual
area addresses set. This attribute is supported only if the node
is an end node and the owning circuit entity's characteristic
type is not x25 da.
o holding timer
Support: L1,L2
Holding time for this adjacency, updated from the router-to-
router Hello messages. This attribute is supported only if both
the node and the adjacency are routers.
o ip addresses
Support: IP
IP addresses of the neighbor node. If these are not known, the
set is empty.
o LAN address
Data link address of the neighboring node on a broadcast circuit.
This status is supported only if the owning circuit entity's
characteristic type is csma-cd.
o LAN priority
Support: L1,L2
Priority of the neighbor of this adjacency for becoming the LAN
level 1 designated router (if the adjacency is a DECnet-Plus level
1 router) or the LAN level 2 designated router (if the adjacency
is a DECnet-Plus level 2 router).
This status is supported only if the owning circuit entity's
characteristic type is csma-cd; and the adjacency is a router
rather than an end node.
o level
Support: L1,L2
The level of the adjacency. This attribute is supported only if
both the node and the adjacency are routers.
Level 1 The adjacency is used for level 1 routing.
Level 2 The adjacency is used for level 2 routing.
Level 1 & 2 The adjacency is used for level 1 and level 2 routing.
Level 0 The usage is undefined.
o neighbor areas
Support: L1,L2
Area addresses of the neighboring node. This attribute is
supported only if both the node and the adjacency are routers
and the owning circuit entity's characteristic type is not x25
da.
o neighbor node id
Support: L1,L2
Node ID of the neighboring node.
o neighbor node type
Support: All
Type of the neighboring node. This status is supported only if
the owning circuit entity's characteristic type is not x25 da.
non-dna The node is not a DNA router.
router
phase iv The node is a Phase IV end node.
endnode
phase iv The node is a Phase IV level 1 router.
level 1
router
phase iv The node is a Phase IV level 2 router.
level 2
router
DECnet-Plus The node is a DECnet-Plus end node.
endnode
DECnet-Plus The node is a DECnet-Plus level 1 router.
level 1
router
DECnet-Plus The node is a DECnet-Plus level 2 router.
level 2
router
DECnet-Plus The node is a DECnet-Plus router.
router
unknown The node type is unknown.
phase iv The node is a Phase IV router.
router
o neighbor protocols supported
Support: IP
Network protocols supported by the neighboring node (either IP or
ISO8473).
o router nets
Support: End
Network Entity Title(s) (NETs) of a neighboring router. This
status is supported only if the adjacency is a level 1 or level
2 router, and the owning circuit entity's characteristic type is
not x25 da.
o state
Support: All
State of the routing circuit adjacency entity. May be one of the
following:
failed
initializing
up
up/dormant
o type
Type of adjacency.
autoconfigured Created by autoconfiguration.
manual Created manually by a create command.
This attribute indicates whether the adjacency has been manually
created, or whether the adjacency was created by means of hello
PDUs. It will always have the value manual when it has been
created by the create command; otherwise, it will have the value
autoconfigured.