1 SHOW 2 AUTO Displays the current settings of auto-load, auto-perm, and any exclude or include lists. Format SHOW AUTO 3 Example $ UCM UCM> SHOW AUTO AUTO LOAD ENABLED AUTO PERM ENABLED EXCLUDE = (*) INCLUDE = (TX, DN) This SHOW AUTO example indicates that all devices are excluded with the exception of TX and DN devices. 2 DEVICE Displays information about devices. Format SHOW DEVICE device-name: 3 Parameter device-name: The name of the device whose characteristics are to be displayed. The device name has the form ddcu, where: dd is the device code-for example, LP. (The driver name corresponds to the device code; in this case, the driver name would be SYS$LPDRIVER.) c is the controller designation A through Z; unless UCM specifies a different letter, all USB devices are A. u is the unit number (0 through 9999.) OpenVMS device names are made up of the two-character device code, followed by the controller designation, the unit number (which can be 1 to 4 characters long), and, finally, a colon (:). 3 Display_Qualifiers /BRIEF /BRIEF (default) Displays summary information for each device. /FULL Displays complete information for each device. 3 Selection_Qualifiers /ALL /ALL (default) Displays all device entries, including those that the /CONFIGURED, /GENERIC, /PERMANENT, /PHYSICAL, and /UNCONFIGURED qualifiers display. /CONFIGURED Displays all the devices connected to the bus that have been configured successfully. /GENERIC Displays the devices that are on the generic device list. /PERMANENT Displays the devices for which the system automatically loads device drivers if the devices are plugged in. /PHYSICAL Displays the devices that are connected to the bus even if drivers for these devices are not loaded. /UNCONFIGURED Displays devices that are attached to the bus and that have drivers, but that do not have entries in the permanent list. (These are also known as tentative devices.) You must execute an ADD DEVICE command to make these devices part of the permanent list. Once the drivers have been added, the device is automatically configured the next time it is plugged in. 3 Example $ UCM UCM> SHOW DEVICE /PERMANENT /FULL DNA3: DEVICE DEVICE_TYPE PERMANENT DEVICE_NAME_ROOT DNA UNIT_NUMBER 3 DRIVER SYS$DNDRIVER.EXE USB_CONFIG_TYPE INTERFACE VENDOR_ID 3519 PRODUCT_ID 768 RELEASE_NUMBER 4352 BUS_NUMBER 1 PATH 1.0.0.0.0.0 DEVICE_CLASS 0 DEVICE_SUB_CLASS 0 DEVICE_PROTOCOL 0 NUMBER_OF_INTERFACES 1 CONFIGURATION_VALUE 2 NUMBER_OF_CONFIGURATIONS 1 SERIAL_NUMBER 2B0301060D97A4C8 MANUFACTURER_STRING QTS PRODUCT_STRING USB 2.0 ATAPI Bridge CONFIGURATION_NUMBER 0 BEGIN_INTERFACE INTERFACE_CLASS 8 INTERFACE_SUB_CLASS 6 INTERFACE_PROTOCOL 80 END_INTERFACE END_DEVICE In this example, the SHOW DEVICE command displays complete information about DNA3:. 2 EVENTS Displays important events that occur on the USB bus. Data displayed can include information about device events, such as removals, connections, unrecognized devices, new devices, and so on. Format SHOW EVENTS 3 Qualifiers /BEFORE /BEFORE=time Selects events that occurred before the specified time. You can specify time as an absolute time, as a combination of absolute and delta times, or as the keyword TODAY (default), TOMORROW, or YESTERDAY. Times are expressed in standard OpenVMS date/time format. /OUTPUT /OUTPUT=file-name Writes the selected events to the specified file. By default, output is sent to the current SYS$OUTPUT device (usually your terminal). You cannot use the /OUTPUT qualifier with the /PAGE qualifier. /PAGE /PAGE /NOPAGE (default) Controls how information is displayed. /PAGE displays events on one screen at a time. You cannot use the /PAGE qualifier with the /OUTPUT qualifier. /PRIORITY /PRIORITY=(keyword[,...]) Selects the event priorities to display. By default, only CRITICAL aand NORMAL event priorities are displayed. Additional messages are available as INFORMATIONAL or debug priority information. The keywords in the following table are valid. CRITICAL and NORMAL are the defaults. Keyword Description CRITICAL Errors and critical information NORMAL Normal event reports such as device configuration INFORMATIONAL Additional informational messages from drivers or UCM DBG1 Debug level 1 information DBG2 Debug level 2 information DBG3 Debug level 3 information ALL All event priorities /SINCE /SINCE=time Selects only those events that occurred on or after the specified time. You can specify time as absolute time, as a combination of absolute and delta times, or as the keyword TODAY (default) or YESTERDAY. /TYPE /TYPE=event-type Selects only the specified type of events. Valid event-types are the following: ALL All event-types (default). CONFIGURED Device was recognized and configured. DECONFIGURE Device was removed from the bus. DRIVER Driver events. UCM UCM server events. UNCONFIGURE Device was recognized but not configured. UNKNOWN Event type is unknown. /VALUE /VALUE=event-number Selects only the events specified by the event number. In a future version of this product, you will be able to use this qualifier as an alternative to the /TYPE qualifier for events that do not have an assigned keyword.